Skip to content
This page was translated from the Traditional Chinese original and has not yet been reviewed by a person. If anything is unclear, the Chinese version is authoritative.

Viewing: HTML | Download the full feature guide as PDF

Troubleshooting: screen and displaying images ​

The panel doesn't change after displaying an image ​

  1. Wait a moment. Refreshing one image takes some time (depending on the model and refresh mode, for example about 6 seconds on the 13.3-inch, about 16 seconds on the 27.6-inch, about 20 seconds on the 32-inch), and the first time you display an image it also needs a little time to convert. Wait until "Refreshing..." disappears from the preview box.
  2. Check the status LED:
    • 2 quick flashes (orange on the full-color LED): the panel is busy and this request was rejected. Wait for the refresh to finish and display the image again.
    • 3 quick flashes (red on the full-color LED): refresh failed.
  3. If the refresh failed, the web page shows "The screen could not be refreshed. Please try again later; if it keeps happening, check the system logs.". Go to System Logs and filter by the ERROR level to see the cause. Common causes:
    • Loose panel ribbon cable
    • Device storage is full (check in Device info)
    • The original image file is corrupted: delete it and upload it again
  4. Try pressing Clear screen first to confirm that the panel can clear the screen.
  5. If clearing the screen also fails, restart the device; if it still fails, contact technical support.
  6. If "Cannot identify the panel; refreshing is paused" or "Panel model not supported; refreshing is paused" appears at the top of the page, the system doesn't display images for now. See Hardware warnings.

Send failed, device may be busy ​

The panel can refresh only one image at a time, and new requests during a refresh are rejected (they are not queued). The panel may be in use because:

  • Someone else is displaying an image
  • A schedule is changing the image at that moment
  • Someone pressed a physical button or the presenter remote
  • The device was just turned and is redrawing

Wait for the current refresh to finish (depending on the model and refresh mode, for example about 6 seconds on the 13.3-inch, about 16 seconds on the 27.6-inch, about 20 seconds on the 32-inch; the status LED returns to standby), then try again.

The image is cut off, has black bars or is distorted ​

SymptomCauseSolution
Black bars at the top and bottom or the sidesFit mode is "Fit" and the image proportions differ from the panelSwitch to "Fill", or remake the image in the panel's proportions
The edges of the image are cut offFit mode is "Fill" or "Crop"Switch to "Fit", or keep important content in the center of the image
The image is stretched wide or tallFit mode is "Stretch"Switch to "Fit" or "Fill"
A PNG background turns blackTransparent backgrounds become a solid colorFill the transparent background with white before uploading

After changing the fit mode or rotation, you must display the image again for it to take effect. The best approach is to make images at the recommended size. See How images are processed for details.

The screen orientation is wrong ​

  1. Only one image is the wrong way? On the Image Display page, select the image, adjust it with "Rotate Image", and display it again.
  2. Everything is the wrong way? Go to G-Sensor Settings:
    • Auto-rotate on: stand the signage upright (orientation isn't detected while it lies flat) and turn it to the correct orientation.
    • Auto-rotate off: check that "Fixed Orientation" is correct.
    • After a change, display an image again or refresh the QR code for it to take effect.
  3. After you turn off auto-rotate and set a fixed orientation, the screen orientation may again follow how the device is physically placed when it restarts. Check it again.
  4. "Orientation sensor (G-sensor) fault" appears at the top of the page: restart the device, or use a fixed orientation instead.
  5. Orientation: at the bottom of the startup screen shows the orientation the system has detected, which you can use for comparison.
  6. Every orientation is always off by 90° or 180°: the model may have been set incorrectly during installation. Contact technical support.

Image upload failed ​

MessageCauseSolution
Response status:400Not an image file, or an SVGUse JPG or PNG instead
Response status:413The image has too many pixels (more than about 80 million for PNG, BMP and so on; JPG can be larger)Reduce the size, or convert it to JPG, and upload again
Response status:500The file is corrupted, the format can't be read (such as iPhone HEIC), or storage is fullConvert to JPG and upload again; check storage space
Lost connection to the deviceThe connection dropped during the uploadReconnect and upload again

See Image gallery and displaying images — Uploading images for details.

I changed a setting but the screen didn't change ​

The following settings take effect only on the next refresh; the screen is not redrawn immediately:

  • Image rotation and fit mode
  • Scan direction, refresh mode, Edge Mask
  • G-Sensor on/off and fixed orientation
  • Screen language (the startup screen has to be shown again)

After a change, display an image on the Image Display page, or press "Refresh QR Code".

The panel shows ghosting or doesn't display correctly ​

  1. Press Clear screen, then display the image again.
  2. Changed the refresh mode recently (only some 13.3-inch panels offer a choice)? Change it back to the mode marked " - Default".
  3. Updated the Tcon firmware recently? Contact technical support and provide the version number.
  4. Edge problems on the 32-inch frameless model: you can turn on or widen the Edge Mask.

The buttons don't respond ​

Status LEDCauseSolution
2 quick flashesThe panel is refreshing (clear screen or QR code gesture)Wait for the refresh to finish, then press again. Changing pages isn't rejected; see Changing pages during a refresh
3 quick flashesThere are no images in the image gallery (when switching images)Upload images first
OffThe device is asleepThe first press wakes it up; press again once it's awake
No change at allThe button service has a problemRestart the device
  • After one press, the system waits about 0.3 seconds before changing the image (to make sure you are not double-pressing; presses must be more than 0.3 seconds apart), and then the refresh takes some more time (depending on the model and refresh mode, for example about 6 seconds on the 13.3-inch, about 16 seconds on the 27.6-inch, about 20 seconds on the 32-inch).
  • If the clear-screen or QR code gestures don't respond, check the current gesture settings in Button trigger settings.

Related: Image gallery and displaying images, Screen orientation and G-Sensor, Status LEDs

Green Ideas Technology