Troubleshooting: connection and management interface
Your phone can't find the device's Wi-Fi
Check in order:
- Does your phone support 5 GHz? The device hotspot uses 5 GHz at the factory; older phones, and some tablets and laptops, that support only 2.4 GHz won't see it at all. Use a newer phone, or ask the administrator to change the hotspot channel to 2.4 GHz (1, 6, 11) in Network settings.
- Is the device in "Station" mode? In this mode the hotspot is off; connect through the on-site Wi-Fi instead. See Network settings — The three network modes.
- Is the device asleep? While asleep, the hotspot is off and the status LED is off. Press a physical button once to wake it up, wait a few seconds, then search again.
- Is the device powered off? If the status LED is off and the buttons don't respond, it may be off or out of power. Check the power.
- Has the device switched to CMS mode? The hotspot isn't broadcast in CMS mode; see CMS / standalone mode switching.
- Did the device just start or wake up? The hotspot needs a little time to start. Wait 1 minute, then search again.
- Can't find the hotspot name? The hotspot name is shown as
SSID:at the bottom of the startup screen. If the panel isn't showing the startup screen, bring it up with the physical button gesture (default: long-press any button for 1.5 seconds, then release immediately). - If everything above is fine and you still can't find it, restart the device (turn the power off and on). If that doesn't solve it, contact technical support.
Connected to Wi-Fi but the web page won't open
- Is the address correct? When connected to the device hotspot, the default address is
http://192.168.100.1(if the hotspot address has been changed in Network settings, use the new address). It starts withhttp, nothttps. - Did your phone switch away automatically? The device hotspot has no internet, so your phone may switch back to another Wi-Fi or mobile data. Go back to Wi-Fi settings, check that you're still connected to the device, and choose "Stay connected"; see Connecting to the device.
- Try turning off mobile data. Some phones send data over mobile data when Wi-Fi has no internet. Turn mobile data off temporarily.
- Did the device just start? The management app needs a little time to start. Wait 1 minute, then refresh.
- Try another browser (Chrome, Safari).
"Lost connection to the device" keeps appearing
This notice means the connection between your phone and the device was lost:
| Possible cause | Fix |
|---|---|
| Your phone switched to another network automatically | Go back to Wi-Fi settings and choose the device hotspot again |
| Too far from the device, weak signal | Move closer to the device; check the signal strength in Network settings |
| The device went to sleep | Press a physical button to wake it up; once the hotspot is back, press "Reconnect" |
| The device is updating software or rebooting | Wait for it to finish, then press "Reconnect" |
| The device is powered off | Handle the power on site |
Automatic reconnection stops after about 3 minutes; after that, press Reconnect or refresh the page.
Disconnected after using it for a while
Most likely the device went to sleep. While someone has the management interface open, the device shows "The device is about to sleep" with a countdown after 15 minutes of idle time, and goes to sleep unless you press "Keep Awake".
- If you want to keep working, press Keep Awake during the countdown.
- If you need to manage the device for a long time, you can temporarily turn off sleep in Sleep settings and turn it back on when you're done.
Page errors after a software update
After a software update, an old page that is still open reloads once automatically when you switch pages. If it still shows errors or a blank screen:
- Refresh the page manually.
- Still wrong: close the tab and type the management interface address again (
http://192.168.100.1by default when connected to the hotspot). - Still wrong: clear the browser cache and try again.
"That action did not take effect" appears after an action
When this notification appears, first check the image gallery, schedules or settings. If the action didn't complete, it's most likely because the connection was lost. Reconnect to the device's Wi-Fi, then do it again. It stays visible while disconnected and closes automatically when the connection comes back.
You see "Response status:number"
This is an error code returned by the device. It usually comes with another message in plain language; go by that message. For what the codes mean, see Message reference.
Related: Connecting to the device, Network settings, Sleep and wake-up