Skip to content
This page was translated from the Traditional Chinese original and has not yet been reviewed by a person. If anything is unclear, the Chinese version is authoritative.

Viewing: HTML | Download the full feature guide as PDF

Cluster: managing devices together ​

Navigation: Settings → System → Cluster

A cluster lets several devices on the same network find each other and pair up as a group. Once they are paired, you can connect your phone or computer to any one of them and view and control the others, and send image sets and schedules to several devices at once. Each device still runs on its own: its images, schedules and sleep carry on as usual. The cluster just saves you from connecting to each device one by one.

Typical uses: a few screens next to a shop counter that should play the same slideshow, or several screens on one floor of an exhibition hall that you want to manage from one place.

The cluster is new in 1.11.0 and is off by default. The tools for working on several devices at once (one-click sync, batch actions, rolling update, overview wall and so on) are described in Cluster tools for multiple devices.

Before you start ​

RequirementDetails
Enable the cluster on every deviceTurn on "Enable cluster" on each device's own "Cluster" page. A device that has not enabled it cannot be found
Connect to the site networkThe device must be connected to the site Wi-Fi in "Wi-Fi" or "Concurrent" mode, or plugged into a network cable. Hotspot-only mode cannot form a cluster; see Waiting for the network
Same networkWe recommend connecting all devices to the same Wi-Fi, or all to the wired network. Devices on different subnets may not be able to reach each other
No "client isolation" on the Wi-FiSome Wi-Fi networks (guest networks in particular) block devices on the same Wi-Fi from connecting to each other. In that case, ask your network administrator to turn off client isolation for that Wi-Fi
Software versionVersions before 1.11.0 have no cluster feature. We recommend updating every device in the cluster to the same version. Some actions do not work on devices with an older version (the screen says "Older version; update it…")

Check with "Network check" first

If you are not sure whether the site network will work, use the Network check on the Cluster page first. Enter the IP address of another device and it tells you, step by step, where things get stuck. You can run the check before the cluster is enabled.

The Cluster page ​

The top of the Cluster page is a list of settings; below it is the "Devices in the cluster" grid. "Refresh" in the upper right reloads the status right away (the page also refreshes itself every 10 seconds).

ItemWhen it appearsDetails
Enable clusterAlwaysA switch. When you turn it on, an "Enable the cluster?" confirmation appears first
Cluster nameThis device is in a clusterClick "Rename" to change it, up to 64 characters
Activity logThis device is in a clusterClick "View"; see Activity log
Network checkAlwaysClick "Check"; see Network check
Manage several devicesThis device is in a cluster that has other membersOverview wall, batch actions, rolling update, change pages together, tile a large image, copy settings; see Cluster tools for multiple devices
Devices in the clusterThe cluster is enabledOne tile per device, with this device first and "Add device" as the last tile

Device tiles ​

Each tile shows a small screen, drawn portrait or landscape to match that device's actual aspect ratio, so you can tell which device is which. Below it are the name, the model ("This device" is added for the device you are connected to), the resolution and software version, and the IP address.

What you seeMeaning
The tile is faded and the screen icon has a gray dot in the cornerThis device is not responding right now
The screen icon has a yellow dot in the cornerThis device has a problem (for example an identity problem); the reason is shown in "Details"

Clicking a tile opens "Details", which lists the model, location, version, IP address, network (hotspot / Wi-Fi / concurrent) and the time of the last response. If there is a problem, the reason is shown at the top.

The "More" menu in the upper right of a tile:

OptionDetails
DetailsSame as clicking the tile
RenameChange this device's "Name" and "Location (optional)", up to 64 characters each. The location is used for grouping; see Groups
Flash itHelps people on site recognize that device; see Find this device
Network checkRuns a network check on this device (for a device that is not responding, this is the first item in the menu)
Remove from clusterOnly on other devices' tiles; see Removing a device and leaving the cluster
Leave clusterOnly on this device's own tile

Devices that are not responding have no "Flash it".

Enabling the cluster ​

  1. Go to Settings → System → Cluster.
  2. Turn on the "Enable cluster" switch.
  3. The "Enable the cluster?" confirmation says "Paired devices on the same network will be able to control each other." Click Enable.
  4. On success, "Cluster enabled" is shown.

Do this once on every device that will be part of the cluster. Once enabled, a device announces itself on the network so that other devices with the cluster enabled can find it.

Waiting for the network ​

If this device does not yet have a usable site network after you enable the cluster, a yellow notice appears below "Enable cluster":

NoticeCause and what to do
This device only runs its hotspot and is not on the site network. Switch to Wi-Fi or concurrent mode under Network, or plug in a cable.Hotspot-only mode cannot form a cluster. Switch modes in Network settings, or plug in a network cable
No address on the site network yet. Check that Wi-Fi is connected or the cable is plugged in.Already in Wi-Fi or concurrent mode, but not connected yet
Cannot read the network status; the network service may still be starting.May appear briefly right after startup; wait a moment and check again

As soon as the network is up, the cluster starts working on its own. You do not need to enable it again.

The cluster service is not running ​

If "The cluster service is not running. Everything else keeps working." appears at the top of the Cluster page, the background service that handles the cluster is not running. Images, schedules and other features keep working. You can click "Retry"; if it keeps happening, restart the device or contact technical support.

Adding and pairing devices ​

Pairing is the only way to add a device to a cluster. Stand next to the device you want to add, and connect your phone or computer to any device that is already in the cluster (when you set up a cluster for the first time, connect to any one of the devices).

Steps ​

  1. On the Cluster page, click the last tile, Add device.
  2. The "Add device" page lists devices found on the network that are not yet in this cluster, each with its name, model, resolution, version and IP. Rows that can be added have Add on the right.
  3. Click Add for the device you want to add.
    • If this device is not in any cluster yet, "Name the cluster" appears first: enter a name (up to 64 characters, for example "1st floor") and click Next. When pairing succeeds, this device and the other one form a new cluster. You can rename it later on the Cluster page.
    • If this device is already in a cluster, you go straight to the next step and the other device joins the current cluster.
  4. A banner with the pairing code appears over the other device's screen. If someone has the other device's management interface open, a "Pairing code" window also pops up there, saying "“Your device's name” wants to add this device to a cluster. Enter this code on that device:" with a countdown.
  5. Enter the 6 digits in the "Enter pairing code" window on your side. It submits automatically once all 6 digits are entered, or you can click OK.
  6. On success, "Added “other device's name”" is shown and you return to the Cluster page. The other device's web page shows "Joined the cluster", and the banner disappears from its screen, which goes back to what it was showing.

The pairing code is never sent over the network. Only someone standing next to that device who can see its screen knows it. This is how you confirm that the device you are adding is the one in front of you.

Pairing code limits ​

ItemRule
Valid for5 minutes. After it expires, click "Add" again
Wrong codeEach pairing code allows 3 tries. A wrong code shows "Wrong code. N tries left"
3 wrong triesThe pairing code becomes invalid. The other device's web page shows "Too many wrong codes; the code is no longer valid"; your side shows a message that pairing has ended
Repeated invalid codesIf 3 pairing codes become invalid within 10 minutes, the other device stops accepting pairing for 5 minutes, and shows "Too many wrong pairing codes. Try again in N seconds" during that time
Pairing at the same timeA device can only pair with one device at a time. If the other device is already pairing with another one, "This device is pairing with “name”" is shown
CancelPairing ends when you close the "Enter pairing code" window on your side, or click "Cancel" on the other device's web page

Devices that cannot be added ​

In the "Add device" list, a device that cannot be added has no "Add" button. Instead, the reason is shown:

ReasonWhat to do
Already in this clusterNo need to add it again
Older version; update it before addingUpdate that device's software first
In another cluster; it must leave that one firstA device can belong to only one cluster at a time. Use "Leave cluster" on that device's Cluster page, or have its cluster remove it
Not respondingCheck that the device is on, not asleep, and that its network is working

When the list is empty, it shows "No other devices yet. They also need the cluster enabled and must be on the same network." The page searches again every 10 seconds.

This device has no cluster, but the other device is already in one

The other device shows "In another cluster; it must leave that one first". If what you actually want is to add this device to the other device's cluster, connect to the other device (or any device in its cluster) instead and add this device from "Add device" there.

Adding manually ​

Some networks stop devices from discovering each other automatically. In that case, click Add under "Add manually" at the bottom of the "Add device" page, enter the other device's IP address (for example 192.168.1.30), and click Add. The other device must also have the cluster enabled.

  • On success, the other device appears in the list above. Then click "Add" to pair as usual.
  • If it fails, the window shows "Could not add it:" followed by the step-by-step results of the Network check.
  • If the format of what you entered is wrong, "Enter an IP address or host name" is shown.

Network check ​

The network check goes through the network between this device and another one, step by step, and tells you why they cannot connect. You can open it from "Network check" on the Cluster page, from the tile menu, or from Details.

The following items are checked in order. If an earlier item fails, the later ones are marked "Not checked: an earlier step failed":

CheckCommon causes when it fails
This device is on the site networkThis device is in hotspot mode, or is not yet connected to Wi-Fi or a network cable
Both devices are on the same subnetOnly a warning: the two devices may be on different Wi-Fi networks. We recommend putting them on the same network
The other device can be reachedThe other device is off, asleep, the address is wrong, or the Wi-Fi has "client isolation" on. The two devices may also be on different networks with no route between them
The other device has the cluster enabledThe other device is on, but the cluster is not enabled
Versions are compatibleOne of the devices has a version that is too old; the screen says which one to update
The devices can find each other automaticallyOnly a warning: the network blocks automatic discovery, so use Adding manually instead. Not checked when this device does not have the cluster enabled yet

For each failed item, the reason and a suggested fix are explained in plain language below it.

Viewing and controlling other devices from one device ​

When this device is in a cluster, a device menu is added to the header of the management interface. The button shows the name of the device you are currently viewing. Open it to see all devices in the cluster, with this device first.

  1. Click the device menu in the header.
  2. Choose another device. The page reloads, and from then on every page shows that device's data: image gallery, image sets, schedules, settings, device info and so on. Whatever you do is done on that device.
  3. A blue banner "Working on “name” (model)" appears at the top of the page to remind you that you are not working on this device.
  4. To come back, click Back to this device on the banner, or choose this device in the device menu.
What the menu showsMeaning
The model or size under the nameCan be chosen
Faded, "Not responding"This device cannot be reached right now and cannot be chosen
Faded, "Asleep (expected to wake at HH:MM)" or "Asleep (wakes when a button is pressed)"This device is asleep; see During sleep and network switching
Faded, "Switching networks; expected back within a minute"This device is switching networks
Faded, "Older version; update it to view it from here"Update that device first
Faded, "Identity problem; rejoin the cluster from that device"See Identity problem
A red dot in the upper right of the buttonA device needs attention; see Alerts

If devices have a "Location" filled in, the menu lists them in sections by location.

The browser remembers the device you chose

After you choose another device, the same browser stays on that device the next time you open the management interface. The device name in the header and the blue banner tell you which device you are working on. If the remembered device is no longer in the cluster, it goes back to this device automatically.

View only

If the banner says "Viewing “name” · view only", that device's version only supports viewing, not control from another device. Update that device to control it.

Actions you can do directly ​

After choosing another device, you can view and use the following pages as usual, with the same effect as connecting to that device directly:

  • Image display and the image gallery (upload, display an image on the panel, clear the screen, delete), PDF collage, image sets
  • Schedules, light schedules and the light
  • Sleep settings, button trigger settings, presenter remote, G-Sensor settings, startup screen, and display settings such as scan direction and refresh mode
  • Time settings, system logs, device info, battery info
  • Software update, Tcon firmware

Uploaded files (images, update packages and so on) can be up to 128 MB.

Actions that ask for confirmation first ​

The following actions take the device offline for a while or carry some risk. A confirmation window appears before they are sent, and they run only after you click "OK":

ActionConfirmation windowAfterwards
Restart"Restart “name”?": it restarts and cannot be reached for about a minuteThe upper right shows "Waiting for “name” to come back…", then "“name” is back online" when it returns. If it has not come back after 5 minutes, "“name” has not come back after 5 minutes. Please check its power and network on site." is shown
Software update (upload an update package)"Update the software on “name”?": it restarts after the update and cannot be reached for a whileThe Software Update page waits for it to come back and shows the result
Tcon firmware update"Update the panel firmware on “name”?": do not turn off that device during the update—

After you change that device's sleep settings, you are reminded that "“name” may go to sleep soon after this change and become unreachable for a while."

Actions that must be done on that device's own page ​

The following features cannot be used from another device. You must connect to that device directly:

FeatureWhy
Network (mode, hotspot, Wi-Fi)Changing the network drops the connection right away
ClusterThe Cluster page always shows the status of the device you are connected to
Mode switch (CMS / standalone)Switching leaves standalone management
Export / import settingsImporting replaces everything on the device and restarts it, and the file has to be uploaded or downloaded on that device's own page
Shut downA device that has shut down cannot be turned on remotely
Factory resetA factory reset makes that device leave the cluster

When another device is chosen, "Network", "Cluster", "Mode Switcher" and "Export / Import" on the Settings page are faded and their description changes to "Open this page on that device". If you click a button like this on other pages, "Open that device's own page to do this" is shown.

Messages you may see when working on another device ​

MessageMeaning
"name" is not respondingThat device is off, has left the network, or the network is down
"name" is asleep and should wake up in about N min / "name" is asleep (press a button on it to wake it up)That device is asleep, and the action was not sent
"name" is switching networks and should be back in about N minTry again later
"name" runs an older version. Update it to view it from here (or control it)Update that device first
"name" did not respond in timeThat device can be reached, but it took too long to respond
"name" refused this device's requestVerification failed, usually because that device no longer recognizes this one (for example, it was removed). Refresh and try again; if it keeps happening, rejoin the cluster
This device is not in the clusterThe device you chose is no longer a member
The file is larger than 128 MBThe uploaded file is too large
Not enough storage space to receive this fileThis device does not have enough storage to pass the file on

During sleep and network switching ​

Before a device goes to sleep or switches networks, it tells the other devices in the cluster, so they know it is "temporarily away" rather than broken.

SituationWhat other devices see
Asleep, with a schedule that will wake it up"Asleep (expected to wake at HH:MM)", with the time shown by your phone's or computer's clock
Asleep, with no schedule (wakes only when a button is pressed)"Asleep (wakes when a button is pressed)"
Switching network modes"Switching networks; expected back within a minute"
Wakes upOnce the network is back, it tells the other devices on its own and can be chosen again
  • A device that is temporarily away cannot be chosen for viewing, and does not appear among the targets you can choose for sync, batch actions and other jobs. These actions are not sent automatically after it wakes up; do them again after it wakes up (the result page has "Resend to failed devices" and "Redo the failed devices" for this).
  • If the notice cannot be sent (for example because the network is already down), sleep or network switching is not blocked; the other devices just mark it "Not responding" after about 3 minutes.
  • A device that leaves without notice (power cut, network cable unplugged) is marked "Not responding" after about 3 minutes without a response.

Sleep timing ​

  • While you use this device to work on another one, this device also counts as in use and does not go to sleep in the middle of what you are doing.
  • Just viewing another device does not count as someone using that device, so it still goes to sleep according to its own sleep settings. However, the countdown warning before sleep, "The device is about to sleep", appears on your screen, and clicking "Keep Awake" delays that device's sleep. See Sleep and wake up.

Removing a device and leaving the cluster ​

ActionHowConfirmation window
Remove another device"More" on that device's tile → "Remove from cluster" → Remove"Remove “name” from the cluster?"
Have this device leave"More" on this device's tile → "Leave cluster" → Leave"Leave the cluster “cluster name”?"
Turn off the clusterTurn off the "Enable cluster" switch. If this device is still in a cluster, it leaves first and then turns off → Leave and turn off"Turning off the cluster leaves “cluster name”"
  • After a device is removed or leaves, other devices can no longer control it, and it can no longer see this cluster.
  • That device's own images and settings are not affected; it just no longer belongs to the cluster.
  • To join again, it must be paired again from a device in the cluster using "Add device".
  • The next time someone opens the Cluster page of a removed device, "This device left the cluster" appears once, saying which device removed it.
  • A factory reset makes this device leave the cluster first and returns it to the cluster-off state.

Identity problem ​

Each device has its own cluster identity. If the entire storage of one device is copied to another, the two devices end up with the same identity. "Details" then says "The same identity appears on another machine (the storage may have been copied), so it is not being synced. Rejoin the cluster from that device." To fix it, have that device leave the cluster and pair it again.

If a device loses its cluster identity data, it leaves the cluster on its own, and the Cluster page shows "This device’s cluster identity data was lost, so it left the cluster “cluster name”. Rejoin when needed."

Related sections: Cluster tools for multiple devices, Network settings, Sleep and wake up, Software update (OTA), Factory reset

Green Ideas Technology